Virus Control Center Mac

    Hi


    I bought a TI Polar yesterday, and installed the Virus Software. When opening the Control Center, I only get the buttons back/restore, burn flash. No librarian, no editor etc... How do I access (no pun intended) these?


    best


    Jan

    That can be accessed from any software hosting AU or VST instruments (Logic, Cubase, Ableton Live etc...)

    -Windows 10 Pro 64bit DAW (Asus ROG Maximus XI Hero + i9-9900)

    -Steinberg Cubase 10 + Steinberg CC121 Controller
    -Steinberg MR816 CSX + Behringer ADA8200
    -iConnectivity MIO10
    -Virus TI2 P0lar
    -Waldorf Pulse (1)
    -Waldorf Blofeld

    -Yamaha AN1x
    -Yamaha Reface DX
    -Clavia Nord Modular G1 Expanded

    -Moog Minitaur
    -Maschine MK3

    -Elektron Octatrack MKII

    -Adam A7X
    https://soundcloud.com/daksha

    I don't know, I only use Cubase, check on Access site, there's a list of supported hosts :)

    -Windows 10 Pro 64bit DAW (Asus ROG Maximus XI Hero + i9-9900)

    -Steinberg Cubase 10 + Steinberg CC121 Controller
    -Steinberg MR816 CSX + Behringer ADA8200
    -iConnectivity MIO10
    -Virus TI2 P0lar
    -Waldorf Pulse (1)
    -Waldorf Blofeld

    -Yamaha AN1x
    -Yamaha Reface DX
    -Clavia Nord Modular G1 Expanded

    -Moog Minitaur
    -Maschine MK3

    -Elektron Octatrack MKII

    -Adam A7X
    https://soundcloud.com/daksha

    Congratulations on getting a Polar!


    Not a DAW, but a AU Host that works very well is Mainstage. I use that all the time, when designing sounds outside of a Cubase project.
    I guess GarageBand should work as well, but proper MIDI setup could be limited.

    Bass Player and Synthesist.
    Virus TI2 Darkstar | Virus TI2 Desktop | Sub 37 | Voyager RME | Machinedrum | Analog Four | Digitone | MPC Live | NI Maschine+
    Mac OS 13.5.1 (Ventura) | Cubase Pro 11.0 | Ableton Live 9.6 | Logic 10.4 | MainStage 3.4 | NI Komplete Ultimate 13 | RME Fireface UFX+

    I'm fiddling with Reaper right now, and I have the plugin loaded, but no sound at all. The Polar is in Sequencer mode, I can select patches, but I have no sound. In preferences, I have chosen the Virus as Audio unit.
    This "Total Integration" isn't as straightforward and total as I hoped....

    Zitat von jan7geerts

    I'm fiddling with Reaper right now, and I have the plugin loaded, but no sound at all. The Polar is in Sequencer mode, I can select patches, but I have no sound. In preferences, I have chosen the Virus as Audio unit.
    This "Total Integration" isn't as straightforward and total as I hoped....


    reaper is not a supported host. please read the documentation, it will save you time. if you have questions, contact support by email. good luck!
    the Virus Control Center you've mentioned earlier on is not the plugin, which is called Virus Control. That's two different things with two different purposes.

    Well, I finally have managed to run VC on Reaper. But I have discovered a bug: when I assign a knob for Delay feedback, it doesn't respond. Other parameters I've tried did, but not that one. Also happens when I use the synth standalone, so it's not a Reaper issue.


    thanks


    Jan