Beiträge von blinde_Q

Zitat von ozon

Important factors to get a pure sine without click:

- Disable all distortion stages of the Virus, including the Character settings which are often forgotten.

Right, for this purpose, I uploaded a clean, empty patch for a while: Virus TI - Empty Bank

i think i found a good solution:

1) load my --init-- preset (in the attachment)

2) change osc to sine

2) set the "Key Mode" to Mono 1 (Common Parameters)

done

thx for the info.

if needed - here is some reset infromation too:

Thema

[Solved] Why can't I to initial the Virus by pressing on Edit Arp butten?

I think I should to initial the virus defination by pressing on the Edit butten of the Arp section as the virus is off. ater that, tow lites is flickering in white colore: the BPM lite is one of them.
The problem is that the lite stay in flicker as long as the butten pressed but nothing else occur. the Virus not initial itself and i have a lot of wrongs in the software.

i must to initial the virus by pressing on Edit. someone know why it isn't give me this option... it related to the USB hub or…

agurvitz

29. August 2009

Beitrag

RE: Virus TI factory reset

Good to know! Thanks for posting this information!
On a related note, a complete list would be nice of all the different combinations, if there are more, of start-up/button press functions such as the arp edit start-up settings reset mentioned above.
Cheers!

PS. Here's an interesting related thread:
Virus Control Center "Restore Factory Settings" loads wrong ROM banks on TI2 Desktop and Polar

GESchwalm

25. Juni 2017

old but good informations:

best way is to contact the support: https://www.virus.info/contact

yes, direct recording with no latency

hi,

did you tried a hard/factory reset? (ARP-EDIT-Reset)

my aproach:

a multipatch of 2 (and 2 midi channels)

i used only the second osc for both patches to use different semitones and detuning.

Patch 1 - osc2 = -4 semitone and detune 118 - Pan Left

Patch 2 - osc2 = 0 semitone and detune 0 - Pan Right

playing note A2

180 HZ left

220 HZ right

zero crossing must be accurate

Edit: i found a better solution: TI2 Sine Without pop

This phenomenon occurs in most synths and samplers. You can try other synthesizers (hardware or software - it doesn't matter). Even if you record it, for example, in Ableton, and loop only a small section (or only one cyle) in Simpler or Sampler, the "amp env pop" is still there. You can smooth it out with amp attack and release, but it's still present. This is related to the amp envelope of the synthesizer and/or sampler.

My workaround:

Resample or record the sine/wave sound from your synthesizer and loop the recorded audio clip somewhere in the middle at zero crossing points (do not crop the clip because you will get some "pop" again) - loop the clip - now you can play/trigger the clip without the "pop".

But as said, if you load that clip in Sampler or Simpler, you get the "pop" sound again.

Hi,

Could you please provide more information? Are you using a PC or laptop, and which USB port are you utilizing - front or mainboard?

Have you tried using other USB ports?

Have you tried different VST versions, such as VST2 or VST3?

Regarding USB issues: Virus TI2 unusable via USB Audio

Zitat von vember

There is an emulator for the DSP that runs B/C ROMS, and another one in a demo-mode limited state that does TI/TI2. I've used both and think it's great that the synths are being preserved but the hardware is still the best option for now.

that must be the donator version:

that looks great to me!

here is the clean link to the maxforlive site: Virus TI2 Control editor

you can only run one instance per hardware. but you have 16 Slots in the plugin one for each preset.

have a look here: Multimode

One reason I switched to Apple back then was "Apple´s Logic DAW". Nowadays, I don't use it anymore.

Zitat von justjoo

Any ideas what could be wrong? I'd just like to send midi notes with the keyboard to Logic.

hi, please give us more information on how your gear is connected.

Virus infection symptoms are: having a TI2 in your hands.

Welcome to the madness!

Zitat von DovGoldman

Last I checked, the emulator runs only the Virus B ROM.

C Rom is working

Under Windows 10/11 the TI, VC, and VST/AU plugins are still running, who knows for how much longer...

You can still use the TI2, albeit possibly with some limitations. (in Windows)

For me: I will generally switch back to the Windows platform since Apple is no longer sustainable for me (except for the iPhone, iPad). Apple's pricing and software policies are more than questionable!

My Mac Pro Tower (€3200) is now over 12 years old and almost useless. Hardware upgrades up to €2000 are a waste of money since the last compatible CPU generation is too weak and some fans cannot be replaced (CPU fans). For around €2500 without tax, I can buy a new PC that far surpasses the performance of a current Mac Pro Tower.

Zitat von alsmrt123

I have a access virus emulator on my pc with the virus b rom on it but I would like to try out the virus a original presets, is there a way to download them?

you need to download: Virus A Series OS 2.80

(as Lioio already mentioned)

You can not import Preset Banks that are in *.mid Format, you have to load the OS

hey, i found them: https://www.virus.info/downloa…g-Systems-(older-versions)

LFO Led Hotfix and older TI OS